PPR पाइप स्थापना ज्ञान
पाइपलाइन कनेक्शन विधियों में वेल्डिंग, गर्म पिघल और थ्रेडेड कनेक्शन शामिल हैं। पीपीआर पाइप गर्म पिघल कनेक्शन सबसे विश्वसनीय, काम करने में आसान, अच्छी हवा जकड़न, उच्च इंटरफ़ेस ताकत है। पाइप कनेक्शन गर्म पिघल कनेक्शन के लिए हाथ से आयोजित वेल्डिंग डिवाइस को अपनाता है। कनेक्शन से पहले पाइप और सामान से धूल और विदेशी पदार्थ को हटा दिया जाना चाहिए। जब मशीन की लाल बत्ती चालू और स्थिर होती है, तो DN से कनेक्ट होने के लिए पाइपलाइन (भाग) को संरेखित करें< 50="" hot-melt="" depth="" of="" 1-2mm,="" dn="">< 110="" hot-melt="" depth="" of="" 2-4mm. when="" connecting,="" insert="" the="" tube="" end="" into="" the="" heating="" sleeve="" without="" rotation="" to="" reach="" the="" predetermined="" depth. at="" the="" same="" time,="" push="" the="" pipe="" fittings="" to="" the="" heating="" head="" without="" rotation="" for="" heating.="" after="" reaching="" the="" heating="" time,="" immediately="" remove="" the="" pipe="" and="" fittings="" from="" the="" heating="" sleeve="" and="" the="" heating="" head="" at="" the="" same="" time,="" and="" insert="" the="" pipe="" and="" fittings="" into="" the="" required="" depth="" rapidly="" without="" rotation="" and="" with="" uniform="" force="" to="" make="" the="" joint="" form="" a="" uniform="" flange. within="" the="" specified="" heating="" time,="" the="" welded="" joint="" can="" be="" corrected,="" but="" rotation="" is="" strictly="" prohibited. when="" heating="" pipes="" and="" fittings,="" prevent="" excessive="" heating="" to="" thin="" the="" thickness. the="" pipe="" is="" deformed="" in="" the="" pipe="" fittings. do="" not="" rotate="" during="" hot="" melt="" intubation="" and="" calibration. there="" shall="" be="" no="" open="" fire="" on="" the="" operation="" site,="" and="" it="" is="" strictly="" prohibited="" to="" dry="" and="" bend="" the="" pipe="" with="" open="" fire. the="" heated="" pipe="" and="" fittings="" should="" be="" aligned="" vertically="" with="" light="" force="" to="" prevent="" bending="" of="" the="" elbow. after="" connection,="" the="" pipe="" and="" pipe="" fittings="" must="" be="" held="" tightly="" for="" enough="" cooling="" time,="" and="" can="" be="" released="" after="" cooling="" to="" a="" certain="" extent. when="" pp-r="" pipe="" is="" connected="" with="" metal="" pipe="" fitting,="" pp-r="" pipe="" with="" metal="" insert="" should="" be="" used="" as="" transition,="" the="" pipe="" fitting="" is="" connected="" with="" pp-r="" pipe="" by="" hot="" melt="" socket,="" and="" when="" connected="" with="" metal="" pipe="" fitting="" or="" hardware="" fittings="" of="" sanitary="" ware,="" thread="" connection="" is="" used,="" and="" polypropylene="" raw="" material="" belt="" should="" be="" used="" as="" sealing="">यदि मोप पूल एक नल से जुड़ा हुआ है, तो उस पर पीपीआर पाइप के अंत में एक आंतरिक कोहनी (थ्रेडेड) स्थापित करें।पाइपलाइन स्थापना की प्रक्रिया में, बहुत अधिक बल न लगाएं, ताकि पेंच बकसुआ फिटिंग को नुकसान न पहुंचे और कनेक्शन पर रिसाव का कारण न बनें। पाइप काटने को विशेष पाइप कैंची द्वारा भी काटा जा सकता है: पाइप कैंची के संगीन को पाइप के व्यास के अनुरूप समायोजित किया जाना चाहिए, और पाइप को काटने पर बल को समान रूप से लागू किया जाना चाहिए। काटने के बाद, फ्रैक्चर को सहायक राउंडर द्वारा गोल किया जाना चाहिए। जब पाइप टूट जाता है, तो अनुभाग को बिना burrs के पाइप की धुरी पर लंबवत होना चाहिए।